Automation equipment manufacturers · Technical presales and sales engineering support
Let the application engineer answer the enquiries that can become orders.
For a maker of drives, controllers, sensors and HMIs, technical presales is the work between a panel builder's part question and a confirmed bill of materials: checking fit, answering compatibility doubts and supporting trials. GullySales sets up the qualification sheet, the query log and the answer bank, and every technical claim stays with your own engineers.
Scope, fee, reporting and term are agreed in writing after we have read your brief and spoken to you.

What technical presales and sales engineering support means
Technical presales support is the work between a buyer's technical question and a signed order: checking an enquiry against what can be built or delivered, preparing demonstrations and evaluation packs, and answering specification queries. GullySales sets up that routine with your sales and engineering teams, keeps the records, and leaves every technical claim to your own specialists.
Also for automation equipment manufacturers
- Sales process for automation equipment manufacturers
- Sales management for automation equipment manufacturers
- Sales strategy for automation equipment manufacturers
- Lead generation for automation equipment makers
- SEO for automation equipment makers
- Social media for automation equipment makers
- Content marketing for automation equipment makers
- Buyer persona for automation equipment makers
Sales and marketing for automation equipment manufacturers, the overview.
Last updated 14 Nov 2026.
For automation equipment manufacturers
Where it usually goes wrong, and what we would do.
“The application engineer is also the help desk”
One or two people know whether your drive will run a particular motor on a particular machine, so every doubt reaches them. A panel builder asking for a wiring check and a distributor asking for a part number land in the same queue. Without a rule for which enquiries earn engineering time, the person who should be supporting the designs that matter spends the day answering questions from buyers who were only comparing prices.
“A bill of materials closes before the answer arrives”
An engineer designing a panel decides on a part while the bill of materials is open, and that moment is short. A question about protocol support or mounting that sits unanswered sends the engineer to the brand whose datasheet already says yes. The loss never shows as a lost quotation, because the order simply goes to another maker. Your own records need to show how long a technical question stayed open.
“Distributors cannot answer, so they steer”
Counter staff at a distributor are asked whether your sensor replaces another brand's part on a machine that has stopped. If nobody there can confirm, they offer the part they know. Your range loses the sale at the one moment a failed machine creates urgency. A shared answer bank that the distributor can read, built from your own datasheets and approved by your engineers, changes what the counter can say.
“Trials and samples prove nothing without a plan”
A demo unit goes to an integrator, runs on a bench, and comes back with no record of what was tested or what the integrator concluded. The result is an opinion rather than evidence. A trial that has a written purpose, the conditions it ran under and a named person who signs the outcome gives the next buyer something to read and gives your sales team something to quote.
What we do
What we deliver for automation equipment manufacturers.
The work available for this need. We agree the deliverables and responsibilities for your engagement in writing.
Technical qualification sheet
A short check applied to each enquiry before engineering time is spent: the part type and ratings asked for, the machine or panel it goes into, the protocol or interface needed, the quantity and the person asking. Your engineering lead writes the rules for what passes, what is redirected to a distributor and what is declined politely.
Result: Check any enquiry from the last month: the sheet shows why it reached engineering or why it did not.
Specification query log
A shared record of each technical question: who asked, which part it concerned, who owned the answer, what was sent and which datasheet or manual page it came from. A repeated question is answered from the log rather than from memory, and an unanswered one is visible to the sales owner.
Result: Open the log and see every technical question still waiting for a reply, with the name of the person who owns it.
Approved answer bank
Replies to the questions panel builders and integrators ask again and again: motor and encoder pairing, supported protocols, mounting and panel space, environmental limits, spare parts and support. Each reply is written from your own documents and approved by a named engineer before any salesperson or distributor may use it.
Result: Each answer in the bank names its source document and the engineer who approved it.
Compatibility and replacement notes
Plain notes on how your parts sit alongside what is already on the machine: which brands' parts they replace, which accessories they need, which settings differ. Where a claim has no test or document behind it, the note says so and leaves the claim out until your engineers supply evidence.
Result: No replacement claim appears in a note without a document your engineers can point to.
Trial and demo unit brief
A written plan for every unit that leaves the building: the buyer's machine, what the trial must show, the conditions, the person who runs it, the date the unit returns and what counts as a pass. The integrator or panel builder reads and agrees the brief before the unit ships.
Result: Every demo unit out in the field has a brief, a named holder and a return date on one list.
Distributor technical handover pack
A pack for distributor counter and technical staff: the range in plain words, the enquiries they may answer themselves, the ones they must pass to you and how to pass them. It uses the approved answers and nothing else, so the distributor says the same thing your engineers would.
Result: A distributor can show which answers it gave and which questions it forwarded to your engineers.
How the result is measured
- Enquiries passed through the qualification sheet before engineering time was spent
- Technical questions logged, with an owner and an approved reply
- Answers given from the approved bank, separate from answers written fresh
Recorded as a baseline before work starts, so every later report has an honest comparison.
Who it is for
This is written for these automation equipment manufacturers.
- Servo and variable frequency drive makers
- PLC, HMI and controller makers
- Sensor, encoder and proximity switch makers
- Relay, contactor and control panel component makers
- Motion control component makers, including linear guides and actuators
- Power supply, signal conditioner and instrumentation makers
- Industrial networking, gateway and IoT device makers
- Machine vision and barcode reader makers
Before you decide
Agree the work. Know how to judge it.
Technical presales and sales engineering support for automation equipment manufacturers: use these checks to prepare, choose the scope, and review what changes.
Bring the right evidence
Review orders by buyer type, offer, and route to market. Include lost proposals and capacity limits so the plan reflects what the team can actually sell and deliver.
Make the scope clear
Choose the target buyer and offer before setting activity targets. Agree responsibilities for finding opportunities, qualification, proposals, and the final commercial decision.
Check the work in use
Check whether the plan explains where the next suitable opportunities will come from and why buyers would choose you. Each priority needs an owner and a way to review progress.
Know when to change course
If the target assumes more delivery capacity or selling time than exists, change the plan. Raising the target does not create either resource.
These are discussion points, not a fixed package. GullySales confirms the deliverables, responsibilities, fee, and term in writing after reading your brief and speaking with you.
Before we start
What to have ready before the work starts.
The records, access and decisions this work needs from automation equipment manufacturers. Anything missing is noted in the written scope, with who will supply it.
- Datasheets, manuals and wiring diagrams
- The answer bank is only as good as the documents behind it. We need the current revision of each datasheet, manual and wiring diagram, with superseded ones marked. When an old datasheet is mixed in, an answer can quote a rating your newer part no longer has, and the buyer finds out on site.
- Recent enquiries with outcomes
- A list of enquiries from the last months, noting which became orders, which went to a rival and which stalled. This is the starting record. Without it we cannot show whether the qualification rules changed anything, and the review at the end rests on opinion.
- A named approving engineer
- One person on your engineering side who can approve or reject each answer and attend the review of closed enquiries. If nobody holds this role, no answer can be verified, and the work shrinks to what the sales team can already confirm from documents.
- Test reports and certificates you hold
- Whatever test evidence, declarations and approvals you actually hold for each product line. Your own adviser decides what may be stated about standards. If a certificate is not in hand, the claim stays out of the answer bank until it is.
- Distributor contact list
- The distributors who stock you and the person at each who handles technical questions. The handover pack needs a real recipient. When it goes to a general mailbox, the counter staff never see it and the old habit of steering to a familiar brand continues.
How it works
How the technical presales and sales engineering support work runs
The work itself, in order. How an engagement starts, from your brief to a written scope, is set out on our method page.
- 1
Read the last technical enquiries
You share a set of recent enquiries that reached your application engineers, with the outcome of each: quoted, lost, declined or still open. We trace which ones were complete, which turned out to be price checks and where an answer waited longest. These findings are the figures the later review is read against.
- 2
Set the qualification rules for panel enquiries
Your engineering lead and your sales lead agree what a complete enquiry contains and what sits outside your range. We write the sheet and the wording for redirecting an enquiry to a distributor or declining it. Your owner approves both before they are used on a live message.
- 3
Build the query log and answer bank
We draft answers from your datasheets, manuals, past replies and any test reports you hold, and mark every statement that has no document behind it. Your technical owner approves, edits or removes each answer. Nothing enters the bank without that approval, and the log starts empty so that new questions are recorded properly.
- 4
Plan the trial for a live opportunity
For one real opportunity, such as an integrator evaluating your drive against a rival, we write the trial brief with your engineers. The buyer reads it and confirms what the trial has to show. We also list the documents the buyer's engineer will want in front of them during the evaluation.
- 5
Agree the sign-off with the buyer
We record which version of the specification the panel builder or OEM accepts, who signs on their side and who signs on yours. Any difference between what was asked and what you offer is written down and approved by your authorised person before it appears in a quotation.
- 6
Hand over and read the result
The sales owner receives the handover note and the engineering lead receives the log. We review closed enquiries with both against the record taken at the start, and change the rules where they failed. The review reports what the log shows; it does not predict orders.
Where this fits
Three pieces of sales work, in this order.
This work sits inside sales process design, at stage 1, prospecting and lead generation. The audit comes before it, and sales management keeps it running.
Step 1
Sales audit
Find where deals are being lost and what to fix first.
Start here if you cannot say where orders are lost.
Step 2 · you are here
Sales process design
One written way to sell, from first enquiry to repeat order.
Start here if every salesperson sells differently.
Step 3
Sales management
A target, a review routine and someone who owns the number.
Start here if the team has targets and no routine.
FAQ
Questions owners ask before they call.
Not here? More answers, or ask on WhatsApp.
Will you answer a panel builder's technical question for us?
Does this replace our application engineer?
Can distributors use the answer bank directly?
What if we do not have a test report for a claim?
Is this the same as a datasheet or product page project?
Will it help us win a bid against a cheaper drive?
How much does it cost?
How long is the contract?
How soon will we see results?
Who will actually do the work?
More for automation equipment manufacturers
Related work to consider.
Closest to this: sales craft
Also for automation equipment manufacturers
Or start from the overview: sales and marketing for automation equipment manufacturers.
Your next practical step
Tell us what you are trying to grow, and we will read it before we call.
Eight short steps, mostly taps. Skip anything you would rather answer on the call.